Új hozzászólás Aktív témák

• #603 Hitman aktív tag

  Új Válasz 2006-10-10 00:02:47 #603

  Új hozzászólás

  Összes hozzászólása itt Válaszok az összes hozzászólására itt Válaszok erre a hozzászólásra

  Privát üzenet küldése

  

  Hitman

  aktív tag

  Sajonos a patronokat nem lehet resetelni semmilyen módszerrel, de van egy alternatív megoldás (ha jól értettem az egyik hozzászóló -neil- leírását): szal a lényeg annyi, hogy az utángyártott patron (természetesen átchippelt) behelyezése után az alacsony tintaszint figyelmeztetés továbbra is működik, ezért ki kell kapcsolni a tintaszint mérést, hogy működjön egyáltalán a cucc, (ekkor elvileg bejegyzi az EEPROM-ba a nyomtató, hogy bibi van nem originaly a patron-- ez természetesen garivesztést von maga után) VISZONT neil állítása szerint az EEPROM-ot lehet resetelni, tartalmát nyomtatni, ami akkor jöhet jól, ha meghal a nyomtató, egyszerűen EEPROM reset, eredeti(használt) canon patronok vissza aztán mehet gariztatni
  
  itt a teljesi hozzászólás, bocsi a hossza miatt:
  
  Here's the present known situation;
  
  The new Canon line of printers present a problem for people wanting to refill their carts with bulk ink. Canon has made the cartridges signal the printer via an electronic counter the number of prints- as opposed to the earlier system of a purely optical device to signal low ink level.
  
  This means, that if you refill the original carts, the printer will not sense a full cart- because its COUNTING PRINTS as well.
  This is how Canon ''encourages'' the consumer to only buy their cartridges, which are obscenely priced.
  
  How to get around this?
  
  Here's the bad news--- THERE IS NO WAY TO RESET THE INK TANK LEVEL INDICATORS from my research, despite rumours here and elsewhere. Don't waste your time asking people to send you the code. It doesn't exist- and that's why its not posting ANYWHERE.
  
  But there is a work-around so you can refill and keep using the printer without shelling out $14 for an official cart.
  
  (please visit my site for all kinds of Canon and other brand printer and ink information - free, non-commercial at
  http://www.neilslade.com/papers/inkjetstuff.html
  
  INK CART REFILLING ON NEW ip4200 Printers (and similar)
  WORK-AROUND
  
  
  Here's what you can do....
  
  METHOD #1 - Easiest, but it disables the ink tank level indicators.
  1) Ignore the low ink indicator, and press the RESET BUTTON to continue printing. If you press and hold the reset button for 5+ seconds, it will disable the counter for that particular ink tank. Refill tank now.
  
  2) Repeat as needed.
  You will get a dire warning that this will void you warranty, blah blah blah. If you do need to take your printer in during warranty and you've disabled ink tank counting, simple reset the entire printer as describe below for the wate tank warning, and nobody will ever know. SAVE YOUR CANON CARTS with a bit of ink left in- your printer will need to have Canon carts installed for warranty service.
  
  3) Eventually you may be warned that the tank is empty. Press reset as above to disable and continue printing.
  
  If you think this entire thing is ridiculous- you are right.
  Get an earlier model that takes un-chip carts, like an ip6000, or ip3000, or i960. Much simpler and you get to use the ink tank indicators after refilling.
  Here's the ip4200 reset options:
  1) With the printer power turned off, while pressing
  the Resume/Cancel button, press and hold the Power
  button. (DO NOT release the buttons. The Power LED
  lights in green to indicate that a function is
  selectable.)
  
  2) While holding the Power button, release the
  resume/Cancel button. (DO NOT release the Power
  button.)
  
  3) While holding the Power button, press the
  Resume/Cancel button 2 times, and then release both
  the Power and Resume/Cancel buttons. (Each time the
  
  Resume/Cancel button is pressed, the Alarm and
  Power LEDs light alternately, Alarm in orange and Power
  in green, starting with Alarm LED.)
  
  4) When the Power LED lights in green, press the
  Resume/Cancel button the specified number of
  time(s)
  setting).
  
  Time(s) LED indication Function Remarks
  0 times Green (Power) Power off When the print head is
  
  not installed, the carriage returns and locks in the
  
  home position capped.
  1 time Orange (Alarm) Service test print .
  2 times Green (Power) EEPROM information print
  3 times Orange (Alarm) EEPROM initialization
  4 times Green (Power) Waste ink counter resetting
  5 times Orange (Alarm) Destination settings After
  entering the destination settings mode, press the
  Resume/Cancel button the specified number of time(s)
  
  to select the destination. For detail, see
  ''Destination settings procedures'' below.
  6 times Green (Power) Print head deep cleaning
  (Cleaning of both black and color)
  7 times Orange (Alarm) Reserved
  8 times Green (Power) CD / DVD check pattern
  9 times Orange (Alarm) CD / DVD print position
  correction (horizontal: X direction)
  10 times Green (Power) CD / DVD print position
  correction (vertical: Y direction)
  11 to 13 times Orange, Green, Orange(Alarm,
  Power,Alarm) Return to the menu selection
  14 times Green (Power) Left margin correction Not used
  
  in servicing.
  15 times Orange (Alarm) Return to the menu selection
  
  
  Time(s) LED indication Destination CD / DVD print
  0 times Green (Power) No change of the destination
  1 time Orange (Alarm) Japan Supported
  2 times Green (Power) Korea Not supported
  3 times Orange (Alarm) US Not supported
  4 times Green (Power) Europe Supported
  5 times Orange (Alarm) Australia Supported

Új hozzászólás Aktív témák