Új hozzászólás Aktív témák

• #20 neduddki nagyúr Maximusz #16

  Új Válasz 2005-08-06 19:34:08 #20

  Új hozzászólás

  Összes hozzászólása itt Válaszok az összes hozzászólására itt Válaszok erre a hozzászólásra

  Privát üzenet küldése

  

  neduddki

  nagyúr

  válasz Maximusz #16 üzenetére

  hi!
  
  eSZT OLVASTRSD???
  
  Technical Specifications of the Sound Blaster Pro
  
  Model Numbers:
  
  CT1600
  CT1900
  Sound Blaster Pro 2 is an 8-bit audio board equiped with a Panasonic/MKE CD-ROM interface.
  
  Hardware Specifications
  
  Frequency Response: 100Hz - 10KHz
  Signal to Noise Ratio: 48 db
  Sampling Rate for Playback/Recording Mono: 5 KHz - 22.1 KHz (4-44.1kHZ Sound BlasterPro only)
  Sampling Rate for Playback/Recording Stereo: 5 KHz - 22.1 KHz (Sound BlasterPro only)
  Supply Voltage Requirement (Loading): +5, +12, -12 Volt
  Current Consumption (Typical): 50, 500, 30 mA respectively
  Microphone Impedance: 600 Ohms
  Line-In Impedance: 39 KOhms
  CD Audio-In Impedance: 50 KOhms (Sound BlasterPro only)
  Microphone Sensitivity: 10 - 200 mVpp
  Line-In Sensitivity: 0 - 2 Vpp
  CD Audio-In Sensitivity: 0 - 2 Vpp (Sound BlasterPro only)
  AD/DA Resolution: 8 bits
  Output Power (Max.): 4 Watts @ 4 Ohms PMPO (Amp out)
  Hardware Settings
  
  Note: Default settings are shown in [brackets]
  
  Interrupt (IRQ): 2, [5], 7, 10
  DMA Channel: 0, [1], 3
  Channel: 0 [1] 3
  DRQ0, DACK0 ON OFF OFF
  DRQ1, DACK1 OFF ON OFF
  DRQ3, DACK3 OFF OFF ON
  
  Joystick I/O Address: 200 Hex
  Joystick: [Enabled] Disabled
  JYEN ON OFF
  
  Audio I/O Address: [220], 240 Hex
  ADDRESS: [220] 240
  22X ON OFF
  24X OFF ON
  
  FM Synthesizer I/O Address: 388 Hex
  Wave Synthesizer I/O Address: Not Applicable
  Sharing DMA [disabled] (DMACTL on pins 1 & 2), or enabled (DMACTL on pins 2 & 3)
  Connectors
  
  Line-In: Yes
  Mic-In: Yes
  Line-Out: No
  Speaker-Out: Yes
  PC Speaker-In: Yes
  Game/Joystick Port: Yes
  CD-ROM Audio-In (Sound Blaster Audio Socket): Yes
  CD-ROM Audio-In (MPC2 Socket): No
  External CD-ROM: Not Applicable
  System Requirements
  
  IBM® PC XT or higher, or 100% compatible motherboard
  VGA
  5 MB of hard disk space for Sound Blaster software.
  MS-DOS® 4.0 or higher, Windows® 3.1 or higher.
  Open 16 bit ISA slot for Sound Blaster Pro cards
  Speakers or headphones
  
  Na akkor megis sb16 volt amin ide volt:
  Model Numbers
  
  CT1730 (Sound Blaster16 non CSP, Panasonic interface)
  CT1740 (Sound Blaster16 CSP, Panasonic interface)
  CT1750 (Sound Blaster16 MCD CSP, Panasonic, Mitsumi, Sony interface)
  CT1770 (Sound Blaster16 SCSI-2, CSP, SCSI-2 Interface)
  CT1779 (Sound Blaster16 SCSI-2, Non CSP, SCSI-2 Interface)
  CT2230 (Sound Blaster16 MCD CSP, Panasonic, Mitsumi, Sony interface)
  CT2230C (Sound Blaster16 CSP, Panasonic interface)
  CT2239 (Sound Blaster16 MCD Non CSP, Panasonic, Mitsumi, Sony interface)
  CT2239C (Sound Blaster16 MCD Non CSP, Panasonic)
  CT2290 (Sound Blaster16 IDE)
  CT2291 (Sound Blaster16 IDE)
  CT2750 (Easy CD, External CD-ROM drive)
  CT2770 (Sound Blaster16 Value, No CSP, Panasonic interface)
  CT2779 (Sound Blaster16 Value, No CSP Panasonic interface)
  CT2919 (Sound Blaster16 No CSP IDE and Panasonic interface)
  The Sound Blaster® 16 card is a 16-bit ISA audio board. It is the single largest group of audio cards from Creative Labs. This card comes equipped with a Panasonic/MKE, Mitsumi, or Sony CD-ROM interface. Some new models of the Sound Blaster16 are equipped with the standard IDE interface as well.
  
  De eldobom az agyam!! SCSI a sb-n??? errul meg ne mhallotam:- )))
  
  udv
  
  neduddki
  
  

  https://facebook.com/bestwax.eu, mailto: bestwax.eu@gmail.com hamarosan: www.bestwax.eu a lustasag fel egesseg, en tejjesen egesseges akarok lenni

Új hozzászólás Aktív témák