Új hozzászólás Aktív témák

  • Intruder2k5

    MODERÁTOR

    válasz mobilizmo #16984 üzenetére

    Szia!

    Próbáld ezzel...

    # This is an example resource file for rTorrent. Copy to
    # ~/.rtorrent.rc and enable/modify the options as needed. Remember to
    # uncomment the options you wish to enable.
    # Minumum amount of peers to connect per torrent, if available.
    min_peers = 1
    # Minumum amount of peers to connect per torrent.
    max_peers = 50
    # Same as above but for seeding completed torrents (-1 = same as downloading)
    # min_peers_seed = 2
    # max_peers_seed = 50
    # Maximum number of simultanious uploads per torrent.
    max_uploads = 5
    # Global download rate in KiB. .0. for unlimited.
    download_rate = 1536
    # Global upload rate in KiB. .0. for unlimited.
    upload_rate = 384
    # Default directory to save downloaded files. Note it doesn.t support
    # space yet.
    directory = /mmc/rtorrent/work/
    # Watch a directory for new torrents, and stop those that have been deleted.
    # schedule = watch_directory,5,5,load_start=/opt/share/torrent/dl/*.torrent
    # schedule = untied_directory,5,5,stop_untied=
    # Close torrents when diskspace is low.
    # schedule = low_diskspace,5,60,close_low_diskspace=100M
    # Default session directory. Make sure you don.t run multiple instance
    # of rtorrent using the same session directory. Perhaps using a
    # relative path?
    session = /mmc/rtorrent/session
    # The ip address reported to the tracker.
    # ip = rakshasa
    # The ip address the listening socket and outgoing connections is
    # bound to.
    # Port range to use for listening.
    port_range = 6890-6890
    # Start opening ports at a random position within the port range.
    # port_random = no
    # Check hash for finished torrents. Might be usefull until the bug is
    # fixed that causes lack of diskspace not to be properly reported.
    check_hash = no
    # Set whetever the client should try to connect to UDP trackers.
    # use_udp_trackers = yes
    # Alternative calls to bind and ip that should handle dynamic ip.s.
    # schedule = ip_tick,0,1800,ip=rakshasa
    # schedule = bind_tick,0,1800,bind=rakshasa
    #
    # Do not modify the following parameters unless you know what you.re doing.
    #
    # Hash read-ahead controls how many MB to request the kernel to read
    # ahead. If the value is too low the disk may not be fully utilized,
    # while if too high the kernel might not be able to keep the read
    # pages in memory thus end up trashing.
    # hash_read_ahead = 10
    # Interval between attempts to check the hash, in milliseconds.
    # hash_interval = 100
    # Number of attempts to check the hash while using the mincore status,
    # before forcing. Overworked systems might need lower values to get a
    # decent hash checking rate.
    # hash_max_tries = 10
    # Max number of files to keep open simultaniously.
    max_open_files = 32
    # Number of sockets to simultaneously keep open.
    max_open_sockets = 32
    # Example of scheduling commands: Switch between two ip.s every 5
    # seconds.
    # schedule = .ip_tick1,5,10,ip=torretta.
    # schedule = .ip_tick2,10,10,ip=lampedusa.
    # Remove a scheduled event.
    # schedule_remove = .ip_tick1.
    # Stop torrents when reaching upload ratio in percent,
    # when also reaching total upload in bytes, or when
    # reaching final upload ratio in percent.
    # example: stop at ratio 2.0 with at least 200 MB uploaded, or else ratio 20.0
    # schedule = ratio,60,60,.stop_on_ratio=200,200M,2000.
    # schedule = ratio,30,60,stop_on_ratio=200
    # Encryption options, set to none (default) or any combination of the following:
    # allow_incoming, try_outgoing, require, require_RC4, enable_retry, prefer_plaintext
    #
    # The example value allows incoming encrypted connections, starts unencrypted
    # outgoing connections but retries with encryption if they fail, preferring
    # plaintext to RC4 encryption after the encrypted handshake
    #
    encryption = allow_incoming,enable_retry,prefer_plaintext
    # Enable DHT support for trackerless torrents or when all trackers are down.
    # May be set to .disable. (completely disable DHT), .off. (do not start DHT),
    # .auto. (start and stop DHT as needed), or .on. (start DHT immediately).
    # The default is .off.. For DHT to work, a session directory must be defined.
    #
    # dht = auto
    # UDP port to use for DHT.
    #
    # dht_port = 6880
    # Enable peer exchange (for torrents not marked private)
    #
    # peer_exchange = yes
    max_memory_usage = 64M
    scgi_port = 127.0.0.1:5000

Új hozzászólás Aktív témák