-
IT café
ASUS WL-500G Premium
Új hozzászólás Aktív témák
-
norb7
tag
Nem teljesen értelek, de itt van, ez a rtorrent konfig fájlja:
# This is an example resource file for rTorrent. Copy to
# ~/.rtorrent.rc and enable/modify the options as needed. Remember to
# uncomment the options you wish to enable.# Minumum amount of peers to connect per torrent, if available.
min_peers = 20# Minumum amount of peers to connect per torrent.
max_peers = 40# Same as above but for seeding completed torrents (-1 = same as downloading)
#min_peers_seed = 10
#max_peers_seed = 20# Maximum number of simultanious uploads per torrent.
max_uploads = 5# Global download rate in KiB. "0" for unlimited.
download_rate = 0# Global upload rate in KiB. "0" for unlimited.
upload_rate = 0# Default directory to save downloaded files. Note it doesn't support
# space yet.
directory = /opt/share/torrent/work/# Watch a directory for new torrents, and stop those that have been deleted.
schedule = watch_directory,5,5,load_start=/opt/share/torrent/dl/*.torrent
schedule = untied_directory,5,5,stop_untied=# Close torrents when diskspace is low.
#schedule = low_diskspace,5,60,close_low_diskspace=100M# Default session directory. Make sure you don't run multiple instance
# of rtorrent using the same session directory. Perhaps using a
# relative path?
session = /opt/share/torrent/session# The ip address reported to the tracker.
#ip = rakshasa# The ip address the listening socket and outgoing connections is
# bound to.
#bind = rakshasa# Port range to use for listening.
port_range = 51777-51777# Start opening ports at a random position within the port range.
#port_random = no# Check hash for finished torrents. Might be usefull until the bug is
# fixed that causes lack of diskspace not to be properly reported.
#check_hash = no# Set whetever the client should try to connect to UDP trackers.
#use_udp_trackers = yes# Alternative calls to bind and ip that should handle dynamic ip's.
#schedule = ip_tick,0,1800,ip=rakshasa
#schedule = bind_tick,0,1800,bind=rakshasa#
# Do not modify the following parameters unless you know what you're doing.
## Hash read-ahead controls how many MB to request the kernel to read
# ahead. If the value is too low the disk may not be fully utilized,
# while if too high the kernel might not be able to keep the read
# pages in memory thus end up trashing.
#hash_read_ahead = 10# Interval between attempts to check the hash, in milliseconds.
#hash_interval = 100# Number of attempts to check the hash while using the mincore status,
# before forcing. Overworked systems might need lower values to get a
# decent hash checking rate.
#hash_max_tries = 10# Max number of files to keep open simultaniously.
#max_open_files = 128# Number of sockets to simultaneously keep open.
#max_open_sockets = <no default># Example of scheduling commands: Switch between two ip's every 5
# seconds.
#schedule = "ip_tick1,5,10,ip=torretta"
#schedule = "ip_tick2,10,10,ip=lampedusa"# Remove a scheduled event.
#schedule_remove = "ip_tick1"# Stop torrents when reaching upload ratio in percent,
# when also reaching total upload in bytes, or when
# reaching final upload ratio in percent.
# example: stop at ratio 2.0 with at least 200 MB uploaded, or else ratio 20.0
#schedule = ratio,60,60,"stop_on_ratio=200,200M,2000"
schedule = ratio,30,60,stop_on_ratio=200# Encryption options, set to none (default) or any combination of the following:
# allow_incoming, try_outgoing, require, require_RC4, enable_retry, prefer_plaintext
#
# The example value allows incoming encrypted connections, starts unencrypted
# outgoing connections but retries with encryption if they fail, preferring
# plaintext to RC4 encryption after the encrypted handshake
#
# encryption = allow_incoming,enable_retry,prefer_plaintext# Enable DHT support for trackerless torrents or when all trackers are down.
# May be set to "disable" (completely disable DHT), "off" (do not start DHT),
# "auto" (start and stop DHT as needed), or "on" (start DHT immediately).
# The default is "off". For DHT to work, a session directory must be defined.
#
# dht = off# UDP port to use for DHT.
#
# dht_port = 6881# Enable peer exchange (for torrents not marked private)
#
# peer_exchange = yes#
# Do not modify the following parameters unless you know what you're doing.
#Lehet hogy ebben van valami hiba?
De amugy ha azt mondjátok, hogy az rtorrent fut, akkor az a kérdésem, hogy a webes felületet hogyan tudom futásra bírni? (Uszítsam rá a rottweilerem? )
Mert nekem weben keresztül az a furcsa, hogy mikor rányomok a beállítások gombra, akkor megismétli a hibaüzenetet. Ezért is írtam korábban, hogy lehet azt nem éri el.
Új hozzászólás Aktív témák
● Olvasd el az összefoglalót!
- Óra topik
- A fociról könnyedén, egy baráti társaságban
- Mikrokontrollerek Arduino környezetben (programozás, építés, tippek)
- VoLTE/VoWiFi
- Samsung Galaxy S21 Ultra - vákuumcsomagolás
- Yettel topik
- Gyúrósok ide!
- Motoros topic
- Spórolós topik
- Samsung Galaxy A55 - új év, régi stratégia
- További aktív témák...
Állásajánlatok
Cég: Ozeki Kft.
Város: Debrecen
Cég: Ozeki Kft.
Város: Debrecen