Új hozzászólás Aktív témák

• #582 arthropod tag rt06 #581

  Új Válasz 2010-02-26 19:00:07 #582

  Új hozzászólás

  Összes hozzászólása itt Válaszok az összes hozzászólására itt Válaszok erre a hozzászólásra

  Privát üzenet küldése

  

  arthropod

  tag

  válasz rt06 #581 üzenetére

  Crunchbang 9.04-ben lévőt: rTorrent 0.8.2/0.12.2

  # This is an example resource file for rTorrent. Copy to
  # ~/.rtorrent.rc and enable/modify the options as needed. Remember to
  # uncomment the options you wish to enable.

  # Maximum and minimum number of peers to connect to per torrent.
  #min_peers = 40
  #max_peers = 100

  # Same as above but for seeding completed torrents (-1 = same as downloading)
  #min_peers_seed = 10
  #max_peers_seed = 50

  # Maximum number of simultanious uploads per torrent.
  #max_uploads = 15

  # Global upload and download rate in KiB. "0" for unlimited.
  #download_rate = 0
  #upload_rate = 0

  # Default directory to save the downloaded torrents.
  #directory = /home/arthropod/torrent/.downloading/

  # Default session directory. Make sure you don't run multiple instance
  # of rtorrent using the same session directory. Perhaps using a
  # relative path?
  #session = /home/arthropod/torrent/.downloading/rtorrent.session/

  # Watch a directory for new torrents, and stop those that have been
  # deleted.
  #schedule = watch_directory,5,5,load_start=/home/arthropod/torrent./watch/*.torrent
  #schedule = untied_directory,5,5,stop_untied=
  # A kész torrenteket az átmeneti könyvtárból a végleges helyükre tesszük
  on_finished=move_complete,"execute=mv,-u,$d.get_base_path=,/home/arthropod/torrent/;d.set_directory=/media/30/NCORE/"
  # Close torrents when diskspace is low.
  #schedule = low_diskspace,5,60,close_low_diskspace=100M

  # Stop torrents when reaching upload ratio in percent,
  # when also reaching total upload in bytes, or when
  # reaching final upload ratio in percent.
  # example: stop at ratio 2.0 with at least 200 MB uploaded, or else ratio 20.0
  #schedule = ratio,60,60,"stop_on_ratio=200,200M,2000"

  # The ip address reported to the tracker.
  #ip = 127.0.0.1
  #ip = rakshasa.no

  # The ip address the listening socket and outgoing connections is
  # bound to.
  #bind = 127.0.0.1
  #bind = rakshasa.no

  # Port range to use for listening.
  #port_range = 6890-6999

  # Start opening ports at a random position within the port range.
  #port_random = no

  # Check hash for finished torrents. Might be usefull until the bug is
  # fixed that causes lack of diskspace not to be properly reported.
  #check_hash = no

  # Set whetever the client should try to connect to UDP trackers.
  #use_udp_trackers = yes

  # Alternative calls to bind and ip that should handle dynamic ip's.
  #schedule = ip_tick,0,1800,ip=rakshasa
  #schedule = bind_tick,0,1800,bind=rakshasa

  # Encryption options, set to none (default) or any combination of the following:
  # allow_incoming, try_outgoing, require, require_RC4, enable_retry, prefer_plaintext
  #
  # The example value allows incoming encrypted connections, starts unencrypted
  # outgoing connections but retries with encryption if they fail, preferring
  # plaintext to RC4 encryption after the encrypted handshake
  #
  # encryption = allow_incoming,enable_retry,prefer_plaintext

  # Enable DHT support for trackerless torrents or when all trackers are down.
  # May be set to "disable" (completely disable DHT), "off" (do not start DHT),
  # "auto" (start and stop DHT as needed), or "on" (start DHT immediately).
  # The default is "off". For DHT to work, a session directory must be defined.
  #
  # dht = auto

  # UDP port to use for DHT.
  #
  # dht_port = 6881

  # Enable peer exchange (for torrents not marked private)
  #
  # peer_exchange = yes

  #
  # Do not modify the following parameters unless you know what you're doing.
  #

  # Hash read-ahead controls how many MB to request the kernel to read
  # ahead. If the value is too low the disk may not be fully utilized,
  # while if too high the kernel might not be able to keep the read
  # pages in memory thus end up trashing.
  #hash_read_ahead = 10

  # Interval between attempts to check the hash, in milliseconds.
  #hash_interval = 100

  # Number of attempts to check the hash while using the mincore status,
  # before forcing. Overworked systems might need lower values to get a
  # decent hash checking rate.
  #hash_max_tries = 10

  Szándékosan nem nyúltam máshoz egyelőre!

  Eladó Voltcraft IPC 1L +8db Eneloop a Vaterán olcsón!!!

Új hozzászólás Aktív témák