-
IT café
ASUS WL-500G Premium
Új hozzászólás Aktív témák
-
Addel
senior tag
ipkg -val felrakott pakkokat hogy lehet leszedni késöbb ?
Még kezdő vagyok linuxban és egy csomo olyat is feltettem a routeremre (kipróbálás céljából) amire nincs szükségem .
[Szerkesztve] -
Addel
senior tag
Találkozott már valaki olyannal hogy router reboot után ctorrent ~200MB-al kevesebbről folytatta a letöltést, mint ahol reboot elött állt ?
Ez mitől lehet ? -
Addel
senior tag
Tudja valaki hogy igaz-e hogy a router country kódját át lehet állítani Német-ről Angol-ra, és akkor max 100mw helyet max 2000mw teljesítményre képes a wifi ?
És ha igen, lelőnek-e érte ? -
Addel
senior tag
válasz kukodajanos #1208 üzenetére
Nálam volt hasonló de Oleg féle firmware-el. Az okozta, hogy egy olcsó sz@r rack-ben volt a hdd-m és túlmelegedés miatt időnként kikapcsolt. Állt. nagy mennyiségü irás-olvasáskor jelentkezett csak.
-
Addel
senior tag
Új firmware Olegtől :
Changes:
1. New Busybox applets (env, cmp, wc, md5sum sha-1)
2. IGMP proxy added (multicast routing [IPTV]) (IP Config | Route > Enable multicast routing?)
3. Added an option to specify 802.11 multicast rate (Wireless | Advanced > Multicast rate)
4. New kernel features (incl. advanced router, new iptables targets)
5. Fixed compile problems with newer Linux ditributions
6. Web interface should no longer show Cable Disconnected status
7. There is now an option to enable/disable DoS protection (Internet Firewall | Basic Config > Enable DoS protection?)
8. Built-in ftp server should now work fine in PASV mode
9. Updated Dropbear to 0.49
10. Updated WiFi to 3.90.38.00
11. Added support for the 128MB of onboard RAM
12. hiddev support
13. FPU emulator fixes
14. WL-HDD IDE fixes - SMART should work now
15. Onboard flash type diagnostic messages
16. Fixed flashfs to respect comment signs
17. flash command now has progress indicator
18. Station/Ethernet Brodge mode should now associate faster to AP after reboot
19. WL500g Deluxe/Premium/WL550gE now rescpect WAN port settings from the web
20. WL500g Premium/WL550gE now better handles OFDM transmitter power setting
21. Added support for /etc/fstab before automount
22. Fixed problems then upgradinf via WiFi using WPA/WPA-PSK
23. Disabled ''power off'' for all units except WL-HDD
24. Pressing EZ SETUP button for 3 seconds would cause /usr/local/sbin/ez-setup to be executed
WL500gp-1.9.2.7-7g -> [link]
[Szerkesztve] -
Addel
senior tag
Én is kezdő vagyok linuxból, és remélem nem mondok nagy hülyeséget, de szerintem az a hiba hogy meg kell adni azt is, hogy mit hova routoljon.
pl.:
iptables -t nat -A PREROUTING -i $1 -p udp --dport 65444 -j DNAT --to-destination $4:65444
ahol:
$1 = WAN interface
$2 = WAN IP
$3 = LAN interface
$4 = LAN IP
$5 = DMZ interface
$6 = DMZ IP -
Addel
senior tag
válasz batkamanó #1268 üzenetére
Én file szervernek nem javaslom, főleg ha több gépet kell kiszolgálnia. Azért mert a max írás/olvasás sebesség amit sikerült kipréselnem belőle kb. 3000KByte és emellé 60-90% procihasználat tásrul a routeren, ami szinte teljesen lefogja ilyenkor azt.
A enhanced-ctorrentet asszem nem kell külön telepíteni ha Seaky féle sctcs-t telepítesz asszem az felteszi a ctorrentet is. -
Addel
senior tag
még annyi, hogy az ''ipkg list_installed'' parancsal lehet megnézni a telepített csomagokat.
-
Addel
senior tag
Nos van más megoldás is elvileg, de én nem próbáltam mert nincs vistám.
A hibát az okozza, hogy a vista csak ugynevezett ''NTLMv2 authentication''-t használ amit a régebbi samba verziók nem támogatnak.
A megoldás amit találtam rá:
Run secpol.msc
Go to: Local Policies > Security Options
Find “Network Security: LAN Manager authentication level”
Change Setting from “Send NTLMv2 response only”
to
“Send LM & NTLM - use NTLMv2 session security if negotiated”
Not a lot of use in my case as I have Vista Home Premium that does not have secpol.msc which is only found in Business an Ultimate. A little more looking revealed:
If you’re running a version of Vista that cannot use secpol.msc, you can edit the registry instead. Just change the value of HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Lsa\
LMCompatibilityLevel from a 3 to a 1.
[Szerkesztve] -
-
Addel
senior tag
Az enhanced-ctorrent maga a torrent kliens de mivel ez csak parancssoros igy macerás használni. Seaky készített hozzá egy webes felületet a ctcs alapján amivel könnyen a webböngésző segítségével lehet manipulálni. Na ez az sctcs.
Most még kérdezhetnéd, hogy miért nem az eredeti ctcs-t használja mindneki.
Azért mert ahhoz perl-t kéne telepíteni a routerre és az állítólag problémás. Úgy tudom van valamiféle microperl, de én nem próbálkoztam vele. -
-
Addel
senior tag
válasz csaboca66 #2090 üzenetére
A yodctcs-vel a config fájlban be lehet állítani, hogy milyen állandó paraméterekkel inditsa a ctorrentet.
#sample config file with compiled in default values
#change these according to your system
torrent-directory=/mnt/disc0_1/torrent/
download-directory=/mnt/disc0_1/
#change user name and password
user=me
password=just
exit-hours=168
exit-ratio=5.6
cache-size=1
restart-torrents=0
download-limit=0
upload-limit=0
#port=18000
#arbitrary arguments to ctorrent
#ctorrent-args=-a -f
#url to prepend in the details box
#detail-url=ftp://192.168.1.1/mnt/disc0_1/
#write-stats=1
#ctorrent=/opt/bin/enhanced-ctorrent
#client-host=localhost:15000
#htmlroot-directory=/opt/share/dctcs/www/darkside.ctcs.gui/[ Szerkesztve ]
-
Addel
senior tag
-
Addel
senior tag
http://wl500g.info/showpost.php?p=47928&postcount=10
Itt le van írva hogy lehet jelszavas hozzáférést csinálni lighttp-hez.
[ Szerkesztve ]
-
Addel
senior tag
samba config file-ba a global részhez
security = SHAREés utána a megosztásoknál
guest ok = noEbben az esetben csak regisztrált samba felhasználó léphet be.
De a "hosts allow =" is sokat segít ahol megadhatsz ip cimet és tartományt is.
Ez működik "hosts deny=" formában is csak ebben az esetben inverz a hatás. -
-
Addel
senior tag
válasz Colonius #3292 üzenetére
Persze, mindkettővel, de a n2hell sajnos csak 0.7.x-es rtorrentel működött, de állítólag nemsokára frissül és akkor jó lesz. Annyi az egész, hogy a configba
scgi_local = /opt/var/run/rpc.socket helyett
scgi_port =127.0.0.1:5000 kellés akkor ntorrentbe ssh kiválaszt és ott
host - router ip-je
port - ssh port (nálam 22)
socket port - 5000
Felhasználó+jelszó amivel használod ssh-t (pl PuTTY-ot)[ Szerkesztve ]